贾向东,赵阳,徐思齐.热处理参数对5052铝合金板材力学性能的影响研究[J].稀有金属材料与工程,0,():-.[Jia Xiang-dong,Zhao Yang,Xu Si-qi.Research on the effect of heat treatment parameters on mechanical properties of 5052 aluminum alloy[J].Rare Metal Materials and Engineering,0,():-].
本文是作者原稿,未经编辑加工,请引用时标明待出版或者标注网页。最终应以正式出版稿为准。
热处理参数对5052铝合金板材力学性能的影响研究
投稿时间:2020-05-11  修订日期:2020-06-25
中文关键词:  铝合金  热处理  力学性能  流变应力  本构模型
基金项目:江苏省高校自然科学基金面上项目(18KJB460020),南京林业大学青年创新基金(CX2018027),南京林业大学高层次(高学历)人才启动基金(GXL2018020)
中文摘要:
      铝合金具有密度低、重量轻、耐腐蚀、比强度高等优点,是结构轻量化设计的首选材料,但是其力学性能受铝合金的最终热处理状态和变形条件的影响很大。以5052-H32铝合金冷轧板为研究对象,借助于单向拉伸试验、硬度测试对不同热处理参数条件下的力学性能进行研究,分析不同热处理工艺参数对5052铝合金力学性能参数的影响机制,结果表明:对5052-H32铝合金进行再次热处理时,可以显著的降低其变形抗力,提高塑性变形能力;在热处理过程中的加热温度起主要作用,在合理的热处理温度和保温时间条件下,冷却方式对5052铝合金的强度、硬度的影响不大。在此基础上,借助Johnson-Cook模型建立了再次热处理后5052铝合金板材的本构模型。
Research on the effect of heat treatment parameters on mechanical properties of 5052 aluminum alloy
英文关键词:Aluminum alloy  Heat treatement  Mechanical properties  Flow stress  Constitutive model
英文摘要:
      Aluminum alloy has the advantages of low density, light weight, corrosion resistance and high specific strength, so it is the first choice material for structural lightweight design. However, its mechanical properties are greatly affected on the final heat treatment state and deformation conditions of aluminum alloy. Take the 5052-H32 as the research object, the mechanical properties was studied under the condition of different heat treatment parameters by uniaxial tensile test and hardness test, and the influence mechanism of different heat treatment parameters on mechanical properties of 5052 aluminum alloy was analyzed, the results showed that, The deformation resistance of 5052-H32 aluminum alloy can be significantly reduced and its plastic deformation ability can be improved during re-heat treatment. The heating temperature plays a major role in the process of heat treatment, the cooling mode has little influence on the strength and hardness of 5052 aluminum alloy under the reasonable heat treatment temperature and holding time. On this basis, the constitutive model of 5052 aluminum alloy after re-heat treatment was established by johnson-cook model.
作者单位
贾向东 1南京林业大学 机械电子工程学院 
赵阳 1南京林业大学 机械电子工程学院 
徐思齐 1南京林业大学 机械电子工程学院 
摘要点击次数: 53
全文下载次数: 0
  查看/发表评论  
关闭